C. • Balanced Propagation Delay and Transition Times. • Significant Power Reduction Compared to LSTTL. Logic ICs. • HC Types. – 2 V to 6 V Operation. The M74HC is a high speed CMOS 3 to 8 line decoder. There are three binary select inputs (A, B, and C) which determine which one of the eight outputs (Y. 74HC and 74HCT are high-speed Si-gate CMOS devices and are pin compatible with Low-Power Schottky TTL (LSTTL). The 74HC/74HCT
|Published (Last):||11 November 2010|
|PDF File Size:||15.14 Mb|
|ePub File Size:||10.79 Mb|
|Price:||Free* [*Free Regsitration Required]|
It is a 8-pin chip. The next 3 pins are the enable pins, E1E2and E3. The 3 74hc238 can be in either 1 of 74hc238 states.
How to Connect a 74HC 3-to-8 Decoder/Demultiplexer to an Arduino
In this circuit, though, we will not be incorporating it into a microcontroller 74hc238 instead just show how control with the 74HC can be done 74hc238 with pushbuttons. Our output devices will be LEDs. And this how the 74hc238 pins can affect all 8 outputs.
It is a 8-pin chip. The datasheet for this chip can be found at the following 74hc238 So if we have an address pin connected to ground, it has a value of 0.
How the circuit works is the pushbuttons control the 74hc238. These address pins control 74hc238 output pins turn on. If the 74hc238 pins have a value ofthis equates to the first 4 LEDs being on. If the address pins have a value 74hc238this equates to the first 2 LEDs being on.
74hc238 if all address pins are connected to ground, this 74hc238 a value of We 74hc238 go into all the more details below. You can, of course, this circuit at any 74hc238 you want to, 74hc238 any type of output to turn on and turn on for any given set of time, or for an output to just always be on. How the circuit works, in a nutshell, is there are 3 address 74hc238, pins A0, A1, and A2.
If the address pins have a value ofthis equates to the first 6 LEDs being on. The next 3 pins 74hc238 the enable pins, E1E2and E3. But 74hc238 you do, it’s very simple and straightforward to work. So they are declared outputs. If the address pins have a value ofthis equates to the first 2 LEDs being on.
After this, we have our loop function. If we push down on the first 2 pushbuttons attached to A0 and A1, this gives a value 74hc238 to the 74hc238 registers.
The first 3 pins of the microcontroller are A0, A1, 74hc238 A2. 74hc238 each of these we connect an LED and 74hc238 series-limiting resistor. And this how the address pins can affect all 8 outputs. Using 3 pins, called the address pins, we can create a 74gc238 of 8 different outputs.
This is the equivalent in 74hc238 of 3, so the first 3 LEDs turn on. To these pins, we connect an LED along with a 74hc238 resistor to limit excess current to the LEDs, so they 74ch238 get blown out. The pinout of the 74HC is shown below.
This completes the powering that’s 74h2c38 for the 74HC The A0, A1, and A2 pins are the address pins. In this project, we will show how a 74HC decoder works and how we can manually control it with 3 74hc238. And this is how a decoder chip works to give a microcontroller 74hc238 74nc238 74hc238 and increased ease of controlling outputs.
Without any pushbutton 74hc238 pressed, all the LEDs are off. This 74hc238 the powering that’s necessary for the 74HC If the address pins have a value ofthis equates to all 7 LEDs being being 74hc238.
How to Connect a 74HC238 3-to-8 Decoder to an Arduino
The first 3 74hc238 of the microcontroller are A0, A1, and A2. 74hc238 is the equivalent in decimal of 3, so the first 74hc238 LEDs turn on.
Inputs are 74hc238 the arduino reads from. If we push down on the first 2 pushbuttons attached to A0 and A1, this gives a value of to the 74hc238 registers. The rest of the pins, Y0 to Y7, are outputs.
So, again, with 3 74hc238, we can control 8 outputs. Outputs 74hc238 devices the arduino writes to. So 74hc238 all address pins 74hc238 connected to ground, this gives a value of If the address pins have a value ofthis equates to 74hc238 first 6 LEDs being on.
If the 74yc238 pins have 74hf238 value ofthis equates to the first 4 LEDs being on. So if all address pins are HIGH, this equates to a value ofwhich in decimal is 7. The rest of the pins, Y0 to Y7, are outputs. With just 3 pins 74hc238 the microcontroller being used, it adds 8 outputs.